OATEY ABS SPECIAL MILKY CLEAR CEMENT

Medium-Bodied Clear ABS cement for ABS pipe systems.

  • Can be used on ABS sewer and drain, waste and vent systems up to 150mm diameter with interference fit
  • Pressure rating 55 bar after 48 hours
  • Fast curing for all non-pressure applications
  • Formulated to eliminate the clean-up problems associated with black ABS cements.
  • Recommended application temperature 4°C to 43°C
  • Meets ASTM D-2235
  • Comes with dauber brush
  • 2 years shelf life after date of Manufacturing

OATEY ABS SPECIAL MILKY CLEAR CEMENT Seal and Bond 1

PRODUCT NUMBER SIZE PACK CARTON WEIGHT CARTON SIZE 
 30922
 473 ml  24  12.7 kg  23 x 27 x35 cm
 
       
 
     

 

Download: Product Data Sheet
Download: Material Safety Data Sheet

INGREDIENTS (CAS Number)
ABS Resin (9003-56-9)
Acetone (67-64-1)
Methyl Ethyl Ketone (78-93-3)

PHYSICAL/CHEMICAL PROPERTIES
Appearance Milky Clear Liquid
Viscosity min. 500 cps @ 23° C ± -16° C
Density 7.39 ± 0.2 lbs/gallon
Lap Shear Strength (minimum per ASTM Standard)
48 hours 55 Bar
Set Up Time
-1° C to 10° C 6 – 7 minutes
10° C to 21° C 5 – 6 minutes
21° C to 32° C 1 – 2 minutes
Shelf Life 3 years from manufacture date
Maximum VOC per SCAQMD 1168/316A or BAAQMD
Method 40: 325 g/L

 

Oatey Special Medium Milky Clear Solvent Cement is recommended for solvent welding nonpressure ABS pipe and fittings up to 150 mm with interference fit.

Read all directions carefully before using this product.

  • Do not breathe vapors. Use only in well ventilated area. If forced air ventilation is used, be sure it does not cause a fire hazard from solvent vapors. If adequate ventilation cannot be provided, wear a NIOSH-approved respirator for organic solvents.
  • Do not use or store near heat, sparks, or flames. Do not smoke, eat or drink when using. Do not take internally. Vapors may accumulate in low places and may ignite explosively.
  • Store and use at temperatures between 4ºC and 43ºC. At temperatures outside of this range, special care must be taken to prepare good joints and prevent exposures to solvents.
  • Stir or shake before using; if jelly-like, don’t use. Keep container closed when not in use.
  • Avoid eye and skin contact - wear safety glasses with side shields and wear rubber gloves.
  • Do not thin.

1. Square pipe ends and remove all burrs and dirt.
2. Check dry fit of pipe and fitting. Pipe should easily go 1/3 of the way into the fitting. If the pipe bottoms, it should be snug.
3. Use a suitable applicator at least 1/2 the size of the pipe diameter. For larger size pipe systems use a natural bristle brush or roller.
4. Clean pipe and fitting. Do not use primer on ABS piping. Apply liberal coat of cement to pipe to the depth of the socket; leave no uncoated surface.
5. Apply a thin coat of cement to inside of fitting; avoid puddling of cement. Puddling can cause weakening and premature failure of pipe or fitting. Apply a second coat of cement to the pipe.
6. Assemble parts QUICKLY. Cement must be fluid. If cement surface has dried, recoat both parts.
7. Push pipe FULLY into fitting using a 1/4 turning motion until pipe bottoms.
8. Hold pipe and fitting together for 30 seconds to prevent pipe push-out – longer at low temperatures. Wipe off excess.
9. Allow 15 minutes for good handling strength and 2 hours cure time at temperatures above 15ºC before hydrostatic pressure testing up to 12 Bar. Longer cure times may be required at temperatures below 15ºC or with pipe diameters over 50 mm. DO NOT TEST WITH AIR.

This product is not for use with caustic or acidic chemical solutions or with pressure piping systems. Consult Oatey
Technical Department for more information.

NSF Standard 61 for PW, DWV, SEWER
Meets ASTM Standard D 2235

UPCNSFLo VOCISO 9001