Favourites
See all new favourites

OATEY PVC HEAVY DUTY CLEAR

Recommended for potable water, pressure pipe, conduit and drain waste and vent pipe systems

  • Heavy Duty Clear cement for use on all classes PVC pipe and fittings. High pressure up to 315mm, low pressure up to 450mm
  • Thick formula fills gaps in large diameter pipe and loose fitting joints
  • Pressure rating 62 bar after 72 hours
  • Recommended application temperature 4°C to 43°C
  • Meets ASTM D-2564
  • Confirms various environmental requirements such as Lo-V.O.C.
  • Comes with dauber brush
  • 3 years shelf life after date of Manufacturing

OATEY PVC HEAVY DUTY CLEAR Seal and Bond 6

PRODUCT NUMBER SIZE PACK CARTON WEIGHT CARTON SIZE 
30863 237 ml 24 7.3 kg  20 x 22 x27 cm
30876 473 ml 24 13.1 kg  23 x 27 x35 cm

Download: Product Data Sheet

Download: Material Safety Data Sheet

INGREDIENTS (CAS Number)
Acetone (67-64-1)
Amorphous Silica (112945-52-5)
Cyclohexanone (108-94-4)
Methyl Ethyl Ketone (78-93-3)
PVC Resin (9002-86-2)
Tetrahydrofuran (109-99-9)

PHYSICAL/CHEMICAL PROPERTIES
Appearance: Clear Liquid
Viscosity min.: 1600 cps @ 23° C ± -16° C
Density: 7.86 ± 0.2 lbs/gallon

Lap Shear Strength (minimum per ASTM Standards)
2 hours: 17 Bar
16 hours:  34 Bar
72 hours: 62 Bar

Set Up Time
1° C to 10° C:  4 – 5 minutes
10°C to 21° C:  2 – 3 minutes
21° C to 32° C:  1 – 2 minutes

Shelf Life
3 years from manufacture date

Maximum VOC per SCAQMD: 1168/316A or BAAQMD
Method: 40: 510 g/L

Oatey Heavy Duty Clear PVC Solvent Cement is recommended for solvent welding all schedules and classes of PVC pipe and fittings up to 315 mm diameter, and non-pressure applications up to 450 mm with interference fit. Heavy Duty Clear PVC Solvent Cement can be used for potable water, sewer and drain, waste and vent systems.

Read all directions carefully before using this product.

  • Do not breathe vapours. Use only in well-ventilated area. If forced air ventilation is used, be sure it does not cause a fire hazard from solvent vapours. If adequate ventilation cannot be provided, wear a NIOSH-approved respirator for organic solvents.
  • Do not use or store near heat, sparks, or flames. Do not smoke, eat or drink when using. Do not take internally. Vapours may accumulate in low places and may ignite explosively.
  • Store and use at temperatures between 4ºC and 43ºC. At temperatures outside of this range, special care must be taken to prepare good joints and prevent exposures to solvents.
  • Stir or shake before using; if jelly-like, don’t use. Keep container closed when not in use.
  • Avoid eye and skin contact - wear safety glasses with side shields and wear rubber gloves.
  • Do not thin.

1. Square pipe ends and remove all burrs and dirt.
2. Check dry fit of pipe and fitting. The pipe should easily go 1/3 of the way into the fitting. If the pipe bottoms, it should be snug.
3. Use a suitable applicator at least 1/2 the size of the pipe diameter. For larger size pipe systems use a natural bristle brush or roller.
4. Clean pipe and fitting with a listed primer.
5. Apply a liberal coat of cement to pipe to the depth of the socket; leave no uncoated surface.
6. Apply a thin coat of cement to the inside of fitting; avoid puddling of cement. Puddling can cause weakening and premature failure of pipe or fitting. Apply a second coat of cement to the pipe.
7. Assemble parts QUICKLY. Cement must be fluid. If cement surface has dried, recoat both parts.
8. Push pipe FULLY into fitting using a 1/4 turning motion until pipe bottoms.
9. Hold pipe and fitting together for 30 seconds to prevent pipe push-out – longer at low temperatures. Wipe off excess.
10. Allow 15 minutes for good handling strength and 2 hours cure time at temperatures above 15ºC before hydrostatic pressure testing up to 12 Bar. Longer cure times may be required at temperatures below 15ºC or with pipe diameters over 50 mm. DO NOT TEST WITH AIR.

This product is not for use with caustic or acidic chemical solutions. Consult Oatey Technical Department for more information.

NSF Standard 61 for PW, DWV, SEWER

Meets ASTM Standard D 2564

UPCNSFLo VOCISO 9001